Tractor Reference

International Harvester 674 Tractor Specs (1973-1977)

Engine, 8F/4R transmission, PTO, serial, official Nebraska-test, and reviewed-manual details, kept with the applicable configuration.

International Harvester 674 Overview

Red International Harvester 674 tractor with an open station on a gravel farm drive.

The International Harvester 674 was built from 1973 through 1977 at Doncaster, England. It was offered with two four-cylinder engines: the D-239 diesel at 239 cubic inches (3.9 L) and the C-200 gasoline engine at 200.3 cubic inches (3.3 L). Both are listed at 2,400 rpm, but engine-specific details and test results need to stay with the fuel type.

The published transmission is an 8-forward, 4-reverse gear drive with a dry-disc clutch. The tractor is listed with open-center hydraulics, a Category II hitch with position and draft control, and an independent 540 PTO. Its 20-gallon fuel tank, 84.5-inch wheelbase, 5,650-pound operating weight, and 7.50-16/16.9-30 agricultural tires provide a useful baseline; fitted equipment can change the final configuration.

Two official Nebraska records make the 674 especially useful to compare. Test 1128 covers the gasoline utility and row-crop 8-speed tractors, while Test 1129 covers the corresponding diesel versions. The reviewed operator, parts, chassis-service, and D-239 engine-service previews below help owners identify the right literature without treating any preview as a complete manual.

Years1973-1977
Engine239 ci 3.9 L | 200.3 ci 3.3 L
Transmissiongear
Rear PTO540 (1.375)
Weight5,650 lbs 2562 kg
Engine choicesD-239 diesel or C-200 gasoline
Fuel tank20 gal / 75.7 L
Year-start serials1973: 100001; 1977: 107555
Nebraska test recordsTest 1128 gasoline; Test 1129 diesel

International Harvester 674 Quick Answers

  • What engines were offered in the IH 674?The listed engines are the International Harvester D-239 four-cylinder diesel at 239 cu in (3.9 L) and the C-200 four-cylinder gasoline engine at 200.3 cu in (3.3 L). Both are listed at 2,400 rpm.
  • How much horsepower does an IH 674 have?Official Nebraska Test 1128 recorded 58.53 PTO hp at rated engine speed and 51.97 maximum-available drawbar hp for the gasoline 8-speed tractor. Test 1129 recorded 61.56 PTO hp and 54.45 drawbar hp for the diesel 8-speed tractor. Those are separate, tested configurations rather than one model-wide rating.
  • What transmission does an IH 674 use?The 674 is listed with a gear transmission offering 8 forward and 4 reverse gears, plus a dry-disc clutch. Match the transmission to the individual tractor before using a service or parts detail.
  • What PTO does an IH 674 use?It is listed with an independent rear PTO and a 540 (1.375) PTO shaft. Confirm the fitted PTO equipment before matching an implement.
  • What is the IH 674 fuel capacity?The listed fuel-tank capacity is 20 gal (75.7 L). Capacity alone does not establish the correct fuel, fill procedure, or maintenance practice for either engine.
  • Where are IH 674 serial numbers listed by year?Published year-start serials are 100001 (1973), 101862 (1974), 103172 (1975), 105946 (1976), and 107555 (1977). The serial plate is listed on the left side of the transmission housing.
  • Which Nebraska tests cover an IH 674?The University of Nebraska archive lists Test 1128 for International 674 Utility and Row Crop Gasoline tractors, and Test 1129 for International 674 Utility and Row Crop Diesel tractors. Both reports are for 8-speed, two-wheel-drive configurations tested in 1973.
  • Which manuals are available for the IH 674?Reviewed previews identify IH-O-674 operator material, TC-163 parts-catalog material, a 674 chassis-service manual, and a multi-model D-239 engine-service manual. Use the complete serial-matched publication for settings, procedures, and part-number decisions.

Engine and Power

The 674 has separately listed D-239 diesel and C-200 gasoline four-cylinder engines. The diesel displaces 239 cu in (3.9 L), while the gasoline engine displaces 200.3 cu in (3.3 L); both are listed at 2,400 rpm. Keep the fuel type with every capacity, service, and test comparison.

Diesel engine

International Harvester D239 / diesel / 4-cylinder / liquid-cooled

Displacement239 ci 3.9 L
Bore Stroke3.875x5.06 inches 98 x 129 mm
Air Cleanerdual stage dry
Compression16:1
Rated Rpm2400
Starter Volts12

Gasoline engine

International Harvester C200 / gasoline / 4-cylinder / liquid-cooled

Displacement200.3 ci 3.3 L
Bore Stroke3.8125x4.39 inches 97 x 112 mm
Air Cleanerdual stage dry
Compression7.33:1
Rated Rpm2400
Starter Volts12

Manufacture years

1973-1977

Transmission

The published 674 transmission is an 8-forward, 4-reverse gear drive with a dry-disc clutch. Both official Nebraska reports are for 8-speed, two-wheel-drive tractors, so their results do not automatically describe a differently equipped machine.

8-speed gear

Typegear
Gears8 forward and 4 reverse
Clutchdry disc

PTO and Hitch

The model is listed with an independent rear PTO and a 540 (1.375) shaft. The 1973 Nebraska reports record 605-606 PTO rpm at their 2,400-rpm rated-engine-speed runs, while the normal operating shaft and fitted equipment still need confirming on an individual tractor.

Rear PTO

independent

Rear PTO type

540 (1.375)

Rear hitch

II

Rear lift

3969 lbs 1800 kg

Hydraulics

The listed system is open center with 13 gpm pump flow. The model is also listed with a Category II rear hitch, position and draft control, and a 3,969 lb rear-lift figure. The operator preview visibly covers auxiliary valves, remotes, and three-point-hitch material, but it is not the complete manual.

Type

open center

Pump flow

13 gpm 49.2 lpm

Fluids, Battery, and Service Facts

The listed fuel capacity is 20 gal (75.7 L). The reviewed operator preview has contents for lubrication, cooling, air cleaning, electrical, preventive maintenance, and specifications; the full matching operator manual is still needed for the correct fluid grade, interval, and procedure.

Fuel tank

20 gal 75.7 L

Battery volts

12

Tires and Dimensions

Listed agricultural tire sizes are 7.50-16 front and 16.9-30 rear, with an 84.5-inch wheelbase and 5,650 lb operating weight. The Nebraska reports tested those tire sizes in particular ballast setups, so wheel, tire, and ballast choices should be checked on the tractor being compared.

Wheelbase

84.5 inches 214 cm

Weight

5,650 lbs 2562 kg

Length

131 inches 332 cm

Width

70 inches 177 cm

Front tire

7.50-16

Rear tire

16.9-30

Electrical

Published electrical information lists negative ground and a 12-volt battery. The operator preview covers the electrical system, and the chassis-service preview includes electrical sections, but either complete publication should be matched before making a repair decision.

Ground

negative

Battery volts

12

Serial Number Lookup

The serial plate is listed on the left side of the transmission housing. Published year-start serials run from 100001 for 1973 to 107555 for 1977, making the serial a useful first step when selecting configuration-sensitive manuals and parts.

1973

100001

1974

101862

1975

103172

1976

105946

1977

107555

Manuals, Parts, and Nebraska Tests

The reviewed IH-O-674 file is an eight-page commercial operator-manual preview. It visibly includes the 674 cover, a detailed contents list for engine operation, hydraulics, PTO, cooling, electrical, wheels, lubrication, preventive maintenance, and specifications, plus an auxiliary-valve and remote-cylinder page. It is not the complete operator manual.

The TC-163 parts-catalog preview is a reviewed 14-page commercial extract with the 674 cover and a model-specific index. Its index separates engine-fuel entries, but it is not a complete serial-matched illustrated catalog. The reviewed chassis-service and D-239 engine-service previews are multi-model references with clearly stated scope, not a substitute for the full matched manuals.

The University of Nebraska archive preserves two official 1973 records. Test 1128 is the gasoline utility/row-crop 8-speed test: 58.53 PTO hp at rated engine speed and 51.97 maximum-available drawbar hp. Test 1129 is the diesel utility/row-crop 8-speed test: 61.56 PTO hp and 54.45 drawbar hp. Each result belongs to its tested fuel and configuration.

Operator manual preview

  • International Harvester 674 operator-manual preview - IH-O-674operation, maintenance, and specifications

    Reviewed eight-page preview with 674 cover, contents, and an auxiliary-valve/remote-cylinder page. It is not the complete manual.

    Open operator-manual preview

Parts catalog

  • International Harvester 674 parts-catalog preview - TC-163parts matching

    Reviewed 14-page preview with the 674 TC-163 cover and a model-specific parts index. It is not a complete serial-matched catalog.

    Open parts-catalog preview

Service manual

  • International Harvester 674 chassis-service preview - IH-S-385,454+operation, maintenance, and specifications

    Reviewed 21-page multi-model chassis-only preview that lists the 674. It is not a complete serial-matched manual.

    Open chassis-service preview
  • International Harvester D-239 engine-service previewoperation, maintenance, and specifications

    Reviewed multi-model diesel-engine preview listing the D-239 and 674. It is not a complete 674 service manual.

    Open D-239 engine-service preview

Tractor test report

  • NTTL Test 1128: International 674 Utility/Row Crop Gasolinetested performance

    Official 1973 gasoline 8-speed, two-wheel-drive report.

    Open Test 1128 record
  • NTTL Test 1129: International 674 Utility/Row Crop Dieseltested performance

    Official 1973 diesel 8-speed, two-wheel-drive report.

    Open Test 1129 record

Parts Checks Before Ordering

Start with the serial number, then confirm the installed engine, 8F/4R transmission, PTO equipment, front axle, wheel, and tire arrangement. The 674 parts preview shows model-specific catalog indexing and distinct engine-fuel entries, but a full serial-matched catalog is required before relying on a part number or fitment.

For service work, the D-239 engine preview and the chassis-only service preview identify useful publication families. They should be matched to the actual engine and chassis before using a setting, torque, adjustment, or procedure.

  • TC-163 674 parts-catalog previewReviewed model-specific index preview; use a complete serial-matched catalog for part-number and fitment decisions.Open parts-catalog preview
  • 674 chassis-service previewReviewed multi-model chassis-only preview; use the complete matching publication for settings and procedures.Open chassis-service preview
  • D-239 engine-service previewReviewed multi-model D-239 engine preview; it does not replace a complete model- and serial-matched service manual.Open D-239 engine-service preview

Accuracy Note

Tractor specifications can vary by year, region, factory configuration, installed equipment, and later repairs. Match serial range, engine, transmission, PTO setup, and model code before ordering parts or doing service work.